Floral works as a focused wall feature for living rooms, bedrooms, and covered outdoor walls when generic filler feels too flat. The Floral Wall Art from Grandmix is a laser-cut galvanized steel piece with a 1.5 cm wall standoff that casts a soft shadow behind the design — turning a flat wall into a 3D focal point. Available in 5 sizes from 18×15 inch (46×38 cm) to 47×39 inch (119×100 cm), in Black or White powder-coated finish — suitable for indoor or outdoor placement.

Why It Works

• 3D shadow effect via 1.5 cm wall standoff: Unlike flat printed canvas or framed prints that sit flush against the wall, integrated spacers lift the piece off the wall — ambient light casts a layered shadow that reads as architectural metalwork rather than mass-market wall art.
• Laser-cut from 1.5 mm galvanized steel: Precision-cut floral motifs hold fine detail (petal curves, stem lines, leaf veins) that flat printed art cannot match in physical depth; the galvanized substrate plus electrostatic powder-coat is rust-resistant under typical outdoor conditions, suitable for both indoor walls and exterior placement.
• 5 sizes scale from accent to feature wall: Smaller 18-24 inch pieces work as solo accents above shelves or desks; 32-39 inch suits sofa walls and bedroom focal walls; the 47-inch size suits larger walls or open-plan living rooms.
• Designed in-house at Grandmix's Türkiye studio: Drawn and prototyped for considered craftsmanship and a more intentional wall presence.

Key Specs

• Dimensions: 5 sizes — 18×15, 24×20, 32×27, 39×33, 47×39 inch (46×38, 61×51, 81×68, 99×83, 119×100 cm)
• Material: 1.5 mm galvanized steel, laser-cut, electrostatic powder-coated; finish in Black or White (rust-resistant under typical outdoor conditions)
• Wall standoff: 1.5 cm via integrated spacers (creates 3D shadow effect)
• Mounting: Keyhole brackets on the back; mounting screws and anchors are included — use anchors appropriate to your wall type and the piece's weight
• Weight: 0.5-3 kg depending on size (smallest 0.5 kg, largest 3 kg)
• Best placement: Indoor walls (bedroom, living room, kitchen-dining) and outdoor walls (covered or open patios, garden settings, exterior accent walls)

What's Included

• Floral wall art piece
• Integrated spacer hardware (pre-installed for 3D wall standoff)
• Keyhole brackets (pre-installed on the back)
• Wall anchors and mounting screws
• Care instructions

How to Hang and Install

Mark the keyhole spacing on the wall, drill pilot holes, insert the included wall anchors, and drive the mounting screws in until the screw heads stand slightly proud of the wall. Hang the piece by aligning the keyhole brackets over the screw heads and sliding down to lock. The 1.5 cm spacer hardware automatically creates the 3D shadow effect once mounted. Most sizes install in under 10 minutes with a basic drill; for 47-inch and larger pieces, a second set of hands helps with alignment.

Care

The galvanized steel substrate plus electrostatic powder-coat is rust-resistant under typical indoor and outdoor conditions. Wipe occasionally with a soft, dry cloth to remove dust. For outdoor placement, the powder-coat sheds water and handles direct rain; rinse periodically with fresh water if exposed to salt-spray (coastal, pool-deck, or seaside settings) and wipe dry after heavy moisture exposure to extend finish life. Avoid abrasive cleaners or chemical solvents on the finish.

Frequently Asked Questions

What size works above a sofa or bed?
For a 6-foot sofa or queen bed, a 32×27 inch or 39×33 inch piece typically anchors the wall well — leaving 8-12 inches of breathing room on each side. For 8-foot sofas or king beds, the 47×39 inch piece is more proportionate. Smaller 18-24 inch pieces work as accents above shelves or desks.

What walls and hardware does it work with?
Mounting screws and anchors are included, but use anchors appropriate to your wall type and the piece's weight. For the 47-inch size or stud-free drywall, anchoring into a stud when alignment allows adds extra security. For exterior masonry or brick, use masonry-rated anchors.

Can I group multiple pieces for a gallery wall?
Yes. Floral Wall Art works as a solo statement or as part of a multi-piece gallery wall. For grouping, mix this with complementary motifs from our broader Metal Wall Art collection — leaf, mountain, or animal silhouettes pair well with floral. Maintain consistent finish (all Black or all White) for cohesion.

Is it suitable for outdoor walls or humid spaces?
Yes. The galvanized steel and powder-coat construction is suitable for indoor and outdoor placement — bedrooms, living rooms, covered patios, garden walls, and exterior accent walls. The powder-coat sheds water and handles direct rain; for coastal or salt-spray exposure, rinse periodically with fresh water and wipe dry after heavy moisture to extend finish life.

How do I clean and maintain it?
Wipe occasionally with a soft, dry cloth or microfiber to remove dust from the cut-out details. For deeper cleaning, a damp cloth with mild non-abrasive detergent works; avoid abrasive cleaners or chemical solvents that can dull the powder-coat finish. The 3D shadow effect is unaffected by routine dusting.

You can check our Shipping Policy page