Sunburst sets a clear visual theme for living rooms, bedrooms, and covered outdoor walls through a wall-mounted metal silhouette. The Sunburst Metal Wall Decor from Grandmix is a laser-cut sunburst silhouette in galvanized steel — radiating-line composition rendered in clean cutwork that reads as design-school graphic art rather than printed reproduction. Available in 5 sizes across Black, Gold, and Gold & Silver finishes.

Why It Works

• Sunburst silhouette in cut steel: Laser-cut radiating lines emanate from a central sun disc — graphic, modern, and reads beautifully above a mid-century-modern sofa, dining buffet, or boho-styled feature wall.
• Five sizes for over-sofa walls: From 18-inch accent to 47-inch oversized — pick by wall width above a 6-foot sofa, console, or master-bed headboard for proportional balance.
• Galvanized steel + powder-coat: Rust-resistant finish handles indoor humidity, sun-room placement, and covered outdoor walls — direct rain on a covered porch is acceptable.
• Grandmix finish check: Cut, coated, packed, and checked so the visible edges, finish, and mounting points arrive ready for everyday placement.

Key Specs

• Dimensions: Five sizes (H × W): 18 x 9 in / 46 x 23 cm; 24 x 12 in / 61 x 30 cm; 32 x 16 in / 81 x 41 cm; 39 x 20 in / 99 x 50 cm; 47 x 24 in / 119 x 60 cm.
• Material: Galvanized steel with electrostatic powder-coat finish (rust-resistant)
• Finishes: Black, Gold, Gold & Silver
• Weight: From about 1.5 kg / 3.3 lb at the smallest size
• Mounting: Wall-mounted; mounting screws and anchors are included, but choose anchors rated for your wall material and the art's loaded weight.

What's Included

• Sunburst Metal Wall Decor (size and finish as ordered)
• Mounting screws and wall anchors
• Care instructions

How to Use and Install

Mark the mounting points on the wall using a level. Drill pilot holes (carbide-tipped bit at low speed for tile installations), insert the included wall anchors, and drive the mounting screws. Hang the artwork on the screws. Install takes under 15 minutes with a basic drill. Choose anchors rated for your wall material and the art's loaded weight.

Care

Wipe the powder-coated galvanized steel with a soft, dry cloth or microfiber to remove dust. For sticky spots or fingerprints, a damp cloth with mild non-abrasive cleaner works; avoid abrasive cleaners or chemical solvents. Designed primarily for indoor walls; covered outdoor placement (porch, patio, balcony) is acceptable including direct rain — the rust-resistant finish sheds water. Rinse off any salt-spray and wipe dry after coastal exposure.

Frequently Asked Questions

Where does this work best?
Living room feature walls, bedroom statement pieces, hallway galleries, dining room accents, home office walls, and entryway focal points all suit this design. The piece works as a single statement above a sofa, console, or bed, or paired with smaller decor elements as part of a curated gallery wall arrangement.

How does it mount to the wall?
Each piece ships with mounting screws and wall anchors. Mark the mounting points with a level for alignment, drill pilot holes (carbide-tipped bit at low speed for tile installations), insert the included anchors, and drive the screws. Choose anchors rated for your wall material and the art's loaded weight — drywall, plaster, masonry, or tile.

Is it safe for outdoor use?
Designed primarily for indoor walls. Covered outdoor placement is acceptable — galvanized steel with electrostatic powder-coat finish is rust-resistant and sheds water, so a covered porch, patio, or balcony with direct rain exposure is fine. Rinse off any salt-spray and wipe dry after coastal exposure for longer finish life.

How do I match the finish to existing decor?
Black suits matte-black, chrome, and modern monochrome interiors; Gold pairs with brass hardware and warm metallic accents; the Gold and Silver two-tone option complements layered metallic palettes and Art Deco furniture. Match the finish to nearby decor accents for the most cohesive look.

How do I clean the wall art?
Wipe the powder-coated steel with a soft, dry microfiber cloth to remove dust. For sticky spots or fingerprints, a damp cloth with mild non-abrasive cleaner works. Avoid abrasive scouring pads or chemical solvents that can dull the finish over time. Rinse off any salt-spray and wipe dry.

You can check our Shipping Policy page